- Manuals
- Brands
- LeakSmart Manuals
- Control Unit
- PRO
- Installation and operation manual
Hide thumbs
-
- Bookmarks
Advertisem*nt
Quick Links
Download this manual
: · o
8850000
8850100
8850200
®
leak:SMART
PRO
Connect. Protect.
Trust.®
Valve
Installation
and Operation
Manual
\· (
•----.
11
\ . ·
O pen
•
.Clo:;a_••· - . i•
-
-
.,
� · 1 · · ·
.. . . -
\ .
-�'52��� -
'-.
-· ,·
I]
winK
Connects directly to
®
ZigBee
main water supply.
Certified Product
Table ofContents
Advertisem*nt
Summary of Contents for LeakSmart PRO
- Page 1 : · o 8850000 8850100 8850200 ® leak:SMART Connect. Protect. Trust.® Valve Installation and Operation Manual \· ( •----. \ . · O pen • .Clo:;a_••· - . i• � · 1 · · · ..- -�'52��� - -·...
- Page 3 (or other ® compatable smart home system) with the leakSMART app. ® Pair your leakSMART Valve and waterproof ® sensors to your leakSMART hub. ® Install your leakSMART Valve to your ® main water supply. PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED.
- Page 4 ® TABLE OF CONTENTS • Homeowner Setup and Operation Valve ............. 5 � Manual Operation Steps ..... 8 � Professional Installation Steps ... 9-10 � • Troubleshooting Valve ............. 11-14 �...
-
Page 5: Valve
It’s never been easier to stay in control of your home’s water supply. Setting up your leakSMART system is as simple as launching an app, pairing with ® your smart home system and getting your leakSMART Valve installed. ® Unpack your leakSMART box and check the contents. - Page 6 • Place your leakSMART Valve near your installation location, so you ® can verify that it is within range of your smart home leakSMART Hub. ™ Verification will be done in pairing mode in APP . • Connect leakSMART Valve to the provided 9V Power Supply and verify ®...
- Page 7 • leakSMART App, should register ‘New Valve’ on the home screen. ® Note: You can manually open/close the leakSMART Valve by pressing the ® ‘Open’ and ‘Close’ buttons located on the front of the valve Or use the toggle button to remotely open and close the valve in the app.
- Page 8 Be protected, (Sensors required) • A leakSMART sensor provides an audible water detection ® alarm, even without connection to your leakSMART ® — but pairing a sensor means the system will signal your leakSMART Valve to automatically shut off your water and ®...
-
Page 9: Manual Operation Steps
® Manual Operation Steps Manual Operation of your leakSMART Valve: ® In the event of repeated error messages from your smart home system that the valve is not automatically opening and closing, the valve may be manually opened or closed. -
Page 10: Professional Installation Steps
• Do not grip plastic motor drive for leverage when installing the valve • Do not install on fire suppression systems or fire sprinkler water lines • Indoor use only Ensure that you have all necessary leakSMART Valve components ®... -
Page 11: Valve
Once air has escaped, your system will go back to mormal pressures. • When the valve is closed, it will display a steady red light and water will stop running. Confirm the valve is functioning properly with the leakSMART App. Sensor(s) and hub. ®... - Page 12 Hub and Sensors. Monitor your smart home system through your ® mobile device and detect a leak. The leakSMART Hub will send a signal to your personal smart device ® providing you with more control and protection for your home. Plus you can easily turn your water supply on and off from anywhere using your smartphone, tablet.
- Page 13 • If AC adapter extension wire was used, unplug both ends and reconnect • Replace batteries • Check that your leakSMART Valve is open by pressing the "Open" button ™ on your Valve No water • Make sure the main water supply valve is open...
-
Page 14: Valve
AC adapter cord connector and also removing a battery if any are installed. Then power back up and procced by pressing the center button 5 times rapidly. Note 2: If resetting the valve while connected to an existing leakSmart system where the ®... - Page 15 ® Device Reset Procedures Sector Gear (Manual Operation) Manual operation: Accessing the sector gear, allows for manual operation of the valve. The sector gear is installed directly to the valve stem. Maintain position of the sector gear if removing, flipping the sector gear upside down reverses operation.
